Hp 5385a Frequency Counter Manual

• Hp 5385a Frequency Counter Manual Online

Your unit looks very clean. Mine arrived and is just a little scuffed up, but good condition.

I've read that the LCD's can bleed, but our's are still good. I know the difference between accuracy and precision, which is more like stability. The manual states an accuracy specification of +/-7.72mHz, if I am interpreting it correctly. (using 10MHz and 1E-7/mo aging rate over 10s gate) I let it warm up for a few hours and measuring my OCXO I am seeing the readings drifting around within a 12mHz window. I'm not sure if that is expected, but thought I would see that last digit toggle between just two values. It might be my setup contributing as it's just a loose oscillator connected to my linear PS with a 2k trimpot on the tuning pin. I haven't found any interesting features like my HP5314A.

(except I just saw the DC input jack. This is good because I imagine one could easily use it with an Arduino to log measurements out in the field). It's drifting more now.

I see almost a full hurt over a couple days and a hundred or so milihurt short term. This I cannot tolerate, I will have to procure an OCXO. It looks like there are some additional changes to the counter board, not just a plug in swap, and I have not found the actual HP oscillator anyway.

Or I wonder if it could be just a noisy tune circuit? Dave bought a Chinese reference for his higher model. Anyone know where he got it or something reasonable? I don't think I can really complain to the seller. They said it came in a lot, but they had it connected and mentioned it looked like a recent cal because it was very close to the input frequency. This is not a high volume seller.

Hp 5385a Frequency Counter Manual Online

I have a similar experience with a HP 5385A with option 004 (oven heated oscillator). After testing I could see (by comparing it to another OCXO in my HP8656B) that it was drifting with temperature, indicating that the heater element is probably defect. Touching the OCXO while powered on, confirms this – it has the same temperature as the surroundings.

This week I received a GPS disciplined 10 MHz frequency reference (Symmetricon TrueTime 600-00 XL-AK). Using that to trigger my scope, I clearly see the drift of the 5385A, while the 8656B is rock solid. My plan is to use the Symmetricon as a common freq.

For all instruments, but that limit my usage of the 5385A to my bench, so I am considering changing the OCXO anyway. Metrologist, did your repair go as planned, and did you find a OCXO that actually fit into the 5385A? I assume, that the OCXO must be tunable, to be sure to get the high precision.

Sorry I missed your post, Adam. Still using an external reference, which is sine wave. I wouldn't think either is a problem.

Thanks for the lead, Tiki. The OCXO's for this board are available on ebay for $6USD from queen.sland, who I bought mine from originally. In my photo, the tuning pin is upper left and I believe the upper right is the oven ready pin. Tiki, where did you attach the ref signal? I don't recall what the innards of the counter looked like, so is your board a drop-in replacement? I 3D printed a dual wall plastic cover for this osc, which has 1/8' sealed air cavities around the sides. I need to make one bigger.

Sorry I missed your post, Adam. Still using an external reference, which is sine wave. I wouldn't think either is a problem. Thanks for the lead, Tiki.

The OCXO's for this board are available on ebay for $6USD from queen.sland, who I bought mine from originally. In my photo, the tuning pin is upper left and I believe the upper right is the oven ready pin. Tiki, where did you attach the ref signal?

I don't recall what the innards of the counter looked like, so is your board a drop-in replacement? I 3D printed a dual wall plastic cover for this osc, which has 1/8' sealed air cavities around the sides.

I need to make one bigger. Here's the schematic. Capacitors are ceramic X7R 0603 except 10uF that are 1206 and L1 is a 0805 ferrite bead. MAX6126AASA has various output voltages. Choose the one that fits your need. R1, R2, R3 must be calculated for your OCXO.

There's a bridge under R1 that you can cut if needed. Some Digikey part numbers: FERRITE BEAD 835 OHM AXIAL 1LN 240-2491-ND FERRITE BEAD 220 OHM 0805 1LN 445-172905-1-ND CAP CER 10UF 10V X7R 1206 445-1602-1-ND TRIMMER 100 OHM 0.5W PC PIN TOP 3296W-101LF-ND L2, C9, C10 was intended to be a low pass filter but first of all I missed a resistor at the output of the OCXO and second, it is not needed, just install a 10 Ohm resistor or even a jumper. Got my board form Miti and in the same day the OCXOs from China, the board looks nice and ALL the OCXO are outputting a nice square wave of 10.0000 MHz, the scratches are exagerated by the lightning and are superficial, the seller is to be recommended, she even put a small gift in the box. Now while I'll get the rest of the BOM, I have to (finally) start either my Rubidium or the GPSDO boards to select one of the OCXO.

BTW, the board looks very nice and professionally done, it arrived from CA to DE in reasonable short time as a postcard letter, very nicely packed, so congrats to Miti and I'll let you know what was the performance of the best OCXO and how my board looks assembles. Also, soon to have three 10MHz OCXO available for DE/EU members.

Cheers, DC1MC EDIT: The story will continue here.